Difference between revisions of "Hh2019sweatshop"
Jump to navigation
Jump to search
Line 19: | Line 19: | ||
=Stations= | =Stations= | ||
− | {{SweatshopItem | + | {{SweatshopItem|Title=Unpacking |
− | |Title=Unpacking | + | |Procedure= |
− | |Requirements= | + | |Requirements=* Empty SAMLA for ESD bags |
− | * Empty SAMLA for ESD bags | ||
* tray for boards | * tray for boards | ||
− | |In= | + | |In=* SAMLA boxes with badge-panels |
− | * SAMLA boxes with badge-panels | + | |Out=* loose badge-panels on trays -> Soldering station, |
− | |Out= | ||
− | * loose badge-panels on trays -> Soldering station, | ||
* <span style="green">bags -> Bagging station</span> | * <span style="green">bags -> Bagging station</span> | ||
}} | }} | ||
− | {{SweatshopItem | + | {{SweatshopItem|Title=Soldering AudioJacks |
− | |Title=Soldering AudioJacks | ||
|Subtitle=Audiojacks are not properly soldered, so we'll fix them. | |Subtitle=Audiojacks are not properly soldered, so we'll fix them. | ||
+ | |Procedure= | ||
|Requirements= | |Requirements= | ||
* 2x JBC Soldering station with wide tip (borrow one from Benadski) | * 2x JBC Soldering station with wide tip (borrow one from Benadski) | ||
Line 43: | Line 40: | ||
}} | }} | ||
− | + | {{SweatshopItem|Title=Depanelizing | |
− | * | + | |Requirements= |
− | * | + | * tablemounted vice, pliers (combinatietang), trashcan |
− | * | + | |In= |
− | * | + | * badge-panels |
+ | |Procedure=* Use vice to break side-rails off | ||
+ | * use pliers to break tabs. | ||
+ | Be careful not to scratch/damage/bend boards. | ||
+ | |Out= | ||
+ | * trays with Badges -> display mounting | ||
+ | * waste -> trash | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Display connecting | |
− | * | + | |Requirements= |
− | * | + | * wooden picks |
− | + | |In= | |
− | * | + | *trays with badges |
+ | * trays with displays | ||
+ | |Procedure= slightly bent flat-cable, pass through hole, open connector, insert cable, close connector | ||
+ | |Out= | ||
+ | *trays with badges with display | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Software | |
− | * | + | |Requirements=* laptops with software, USB cables and hubs |
− | * | + | |In=*trays with badges with display |
− | * | + | |Procedure=*connect badge and wait until autotester appears, if final image shows: pass! |
− | * | + | |Out=*trays with badges that pass -> mounting |
+ | *trays with badges that fail -> rework | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Display Mounting | |
− | * | + | |Requirements=* gluedot-gun, Alklanet, microfibercloth |
− | * | + | |In=*trays with badges |
− | * | + | |Procedure=*degrease PCB and display, apply two gluedots on PCB, glue display on PCB |
− | * | + | |Out=*trays with badges with a mounted display -> Bagging |
+ | }} | ||
− | + | {{SweatshopItem|Title=Bagging | |
− | * | + | |Requirements=* Heat-sealer, scissors |
− | * | + | |In=*trays with badges with a mounted display, ESD bags |
− | * | + | |Procedure=*Three badges in bags, seal, cut into separate packs. |
− | * | + | |Out=*badges in ESD bags -> Packing |
+ | }} | ||
− | + | {{SweatshopItem|Title=Packing | |
− | * | + | |Requirements=* Badge-kits, HackerHotel stickers, Sponsor Sticker, Revspace sticker, IR Receiver, empty SAMLA crate |
− | * | + | |In=*badges in ESD bags |
− | * | + | |Procedure=* add badge, stickers and IR receiver to bag, |
− | * | + | * deflate |
+ | * ziplock | ||
+ | * crate | ||
+ | |Out=*complete badge kits! | ||
+ | }} |
Revision as of 15:15, 6 February 2019
Contents
Event
Saturday February 9 we will sweatshop 300 badges together :)
Location will be Revspace (The Hague) and we'll start at 13:00. We estimate everything should be done in approximately 2 hours, maybe even less. Maybe more when a crisis arrises ;)
People
- Sebastius
- Jnx
- Renze
- Tom + 1
- Bugblue
- Relocker
- Obitoo
- Jelle
- Rowan8k
- Maeddoc
- Bef0re + 1
- JanHenrik
Stations
Unpacking
Requirements |
|
---|---|
Procedure | |
What comes in |
|
What comes out |
|
Soldering AudioJacks
Audiojacks are not properly soldered, so we'll fix them.
Requirements |
|
---|---|
Procedure | |
What comes in |
|
What comes out |
|
Depanelizing
Requirements |
|
---|---|
Procedure |
Be careful not to scratch/damage/bend boards. |
What comes in |
|
What comes out |
|
Display connecting
Requirements |
|
---|---|
Procedure |
slightly bent flat-cable, pass through hole, open connector, insert cable, close connector |
What comes in |
|
What comes out |
|
Software
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|
Display Mounting
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|
Bagging
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|
Packing
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|