Difference between revisions of "Hh2019sweatshop"
Jump to navigation
Jump to search
(Created page with " =Stations= ==Unpacking== *Requirements: Empty SAMLA for ESD bags, tray for boards *What comes in: SAMLA boxes with badge-panels *What comes out: loose badge-panels on trays -...") |
m |
||
Line 1: | Line 1: | ||
+ | =Event= | ||
+ | Saturday February 9 we will sweatshop 300 badges together :) | ||
+ | |||
+ | Location will be Revspace (The Hague) and we'll start at 13:00. We estimate everything should be done in approximately 2 hours, maybe even less. Maybe more when a crisis arrises ;) | ||
+ | |||
+ | =People= | ||
+ | * Sebastius | ||
+ | * Jnx | ||
+ | * Renze | ||
+ | * Tom + 1 | ||
+ | * Bugblue | ||
+ | * Relocker | ||
+ | * Obitoo | ||
+ | * Jelle | ||
+ | * Rowan8k | ||
+ | * Max | ||
+ | * Bef0re + 1 | ||
+ | * JanHenrik | ||
+ | |||
=Stations= | =Stations= |
Revision as of 14:43, 6 February 2019
Contents
Event
Saturday February 9 we will sweatshop 300 badges together :)
Location will be Revspace (The Hague) and we'll start at 13:00. We estimate everything should be done in approximately 2 hours, maybe even less. Maybe more when a crisis arrises ;)
People
- Sebastius
- Jnx
- Renze
- Tom + 1
- Bugblue
- Relocker
- Obitoo
- Jelle
- Rowan8k
- Max
- Bef0re + 1
- JanHenrik
Stations
Unpacking
- Requirements: Empty SAMLA for ESD bags, tray for boards
- What comes in: SAMLA boxes with badge-panels
- What comes out: loose badge-panels on trays -> Soldering station, bags -> Bagging station
Soldering AudioJacks
Audiojacks are not properly soldered, so we'll fix them.
- Requirements: 2x JBC Soldering station with wide tip, proper thin solder (borrow one from Benadski)
- What comes in: Badge-panels
- What comes out: Badge-panels with better soldered audio jacks -> Depanelizing
Depanelizing
- Requirements: tablemounted vice, pliers (combinatietang), trashcan
- What comes in: badge-panels
- Procedure: Use vice to break side-rails off, use pliers to break tabs. Be careful not to scratch/damage/bend boards.
- What comes out: trays with Badges -> display mounting, waste -> trash
Display connecting
- Requirements: wooden picks
- What comes in: trays with badges, trays with displays
- Procedure: slightly bent flat-cable, pass through hole, open connector, insert cable, close connector
- What comes out: trays with badges with display
Software
- Requirements: laptops with software, USB cables and hubs
- What comes in: trays with badges with display
- Procedure: connect badge and wait until autotester appears, if final image shows: pass!
- What comes out: trays with badges that pass -> mounting, trays with badges that fail -> rework
Display Mounting
- Requirements: gluedot-gun, Alklanet, microfibercloth
- What comes in: trays with badges
- Procedure: degrease PCB and display, apply two gluedots on PCB, glue display on PCB
- What comes out: trays with badges with a mounted display -> Bagging
Bagging
- Requirements: Heat-sealer, scissors
- What comes in: trays with badges with a mounted display, ESD bags
- Procedure: Three badges in bags, seal, cut into separate packs.
- What comes out: badges in ESD bags -> Packing
Packing
- Requirements: Badge-kits, HackerHotel stickers, Sponsor Sticker, Revspace sticker, IR Receiver, empty SAMLA crate
- What comes in: badges in ESD bags
- Procedure: add badge, stickers and IR receiver to bag, deflate, ziplock, crate
- What comes out: complete badge kits!