Difference between revisions of "Hh2019sweatshop"
Jump to navigation
Jump to search
m |
(→People) |
||
(4 intermediate revisions by 2 users not shown) | |||
Line 14: | Line 14: | ||
* Jelle | * Jelle | ||
* Rowan8k | * Rowan8k | ||
− | * | + | * Maeddoc |
* Bef0re + 1 | * Bef0re + 1 | ||
* JanHenrik | * JanHenrik | ||
− | + | * Stegen | |
=Stations= | =Stations= | ||
− | + | {{SweatshopItem|Title=Unpacking | |
− | * | + | |Procedure= |
− | * | + | |Requirements=* Empty SAMLA for ESD bags |
− | * | + | * tray for boards |
+ | |In=* SAMLA boxes with badge-panels | ||
+ | |Out=* loose badge-panels on trays -> Soldering station, | ||
+ | * <span style="green">bags -> Bagging station</span> | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Soldering AudioJacks | |
− | Audiojacks are not properly soldered, so we'll fix them. | + | |Subtitle=Audiojacks are not properly soldered, so we'll fix them. |
− | * | + | |Procedure= |
− | * | + | |Requirements= |
− | * | + | * 2x JBC Soldering station with wide tip (borrow one from Benadski) |
+ | * proper thin solder | ||
+ | |In= | ||
+ | * Badge-panels | ||
+ | |Out= | ||
+ | * Badge-panels with better soldered audio jacks -> Depanelizing | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Depanelizing | |
− | * | + | |Requirements= |
− | * | + | * tablemounted vice, pliers (combinatietang), trashcan |
− | * | + | |In= |
− | * | + | * badge-panels |
+ | |Procedure=* Use vice to break side-rails off | ||
+ | * use pliers to break tabs. | ||
+ | Be careful not to scratch/damage/bend boards. | ||
+ | |Out= | ||
+ | * trays with Badges -> display mounting | ||
+ | * waste -> trash | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Display connecting | |
− | * | + | |Requirements= |
− | * | + | * wooden picks |
− | + | |In= | |
− | * | + | *trays with badges |
+ | * trays with displays | ||
+ | |Procedure= slightly bent flat-cable, pass through hole, open connector, insert cable, close connector | ||
+ | |Out= | ||
+ | *trays with badges with display | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Software | |
− | * | + | |Requirements=* laptops with software, USB cables and hubs |
− | * | + | |In=*trays with badges with display |
− | * | + | |Procedure=*connect badge and wait until autotester appears, if final image shows: pass! |
− | * | + | |Out=*trays with badges that pass -> mounting |
+ | *trays with badges that fail -> rework | ||
+ | }} | ||
− | + | {{SweatshopItem|Title=Display Mounting | |
− | * | + | |Requirements=* gluedot-gun, Alklanet, microfibercloth |
− | * | + | |In=*trays with badges |
− | * | + | |Procedure=*degrease PCB and display, apply two gluedots on PCB, glue display on PCB |
− | * | + | |Out=*trays with badges with a mounted display -> Bagging |
+ | }} | ||
− | + | {{SweatshopItem|Title=Bagging | |
− | * | + | |Requirements=* Heat-sealer, scissors |
− | * | + | |In=*trays with badges with a mounted display, ESD bags |
− | * | + | |Procedure=*Three badges in bags, seal, cut into separate packs. |
− | * | + | |Out=*badges in ESD bags -> Packing |
+ | }} | ||
− | + | {{SweatshopItem|Title=Packing | |
− | * | + | |Requirements=* Badge-kits, HackerHotel stickers, Sponsor Sticker, Revspace sticker, IR Receiver, empty SAMLA crate |
− | * | + | |In=*badges in ESD bags |
− | * | + | |Procedure=* add badge, stickers and IR receiver to bag, |
− | * | + | * deflate |
+ | * ziplock | ||
+ | * crate | ||
+ | |Out=*complete badge kits! | ||
+ | }} |
Latest revision as of 17:26, 6 February 2019
Contents
Event[edit]
Saturday February 9 we will sweatshop 300 badges together :)
Location will be Revspace (The Hague) and we'll start at 13:00. We estimate everything should be done in approximately 2 hours, maybe even less. Maybe more when a crisis arrises ;)
People[edit]
- Sebastius
- Jnx
- Renze
- Tom + 1
- Bugblue
- Relocker
- Obitoo
- Jelle
- Rowan8k
- Maeddoc
- Bef0re + 1
- JanHenrik
- Stegen
Stations[edit]
Unpacking[edit]
Requirements |
|
---|---|
Procedure | |
What comes in |
|
What comes out |
|
Soldering AudioJacks[edit]
Audiojacks are not properly soldered, so we'll fix them.
Requirements |
|
---|---|
Procedure | |
What comes in |
|
What comes out |
|
Depanelizing[edit]
Requirements |
|
---|---|
Procedure |
Be careful not to scratch/damage/bend boards. |
What comes in |
|
What comes out |
|
Display connecting[edit]
Requirements |
|
---|---|
Procedure |
slightly bent flat-cable, pass through hole, open connector, insert cable, close connector |
What comes in |
|
What comes out |
|
Software[edit]
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|
Display Mounting[edit]
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|
Bagging[edit]
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|
Packing[edit]
Requirements |
|
---|---|
Procedure |
|
What comes in |
|
What comes out |
|